KIT CONSISTS OF:
No. Qty. Part No. Description
ADVANCE ADAPTERS, INC. P/N: 50-5761
P.O. Box 247, 4320 Aerotech Center Way Old Part No:
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-01-13
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the
components will void any possible warranty or return privileges. If you do not fully understand modifications or changed that will be required to complete your
conversion, we strongly recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance
Adapter components. We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related
equipment. These manual are normally available at automotive dealerships and parts stores.
GM 4L60E AUTOMATIC TO
TOYOTA TRUCK (23 SPLINES)
1. 1 51-0405 4L60E / UNIVERSAL ADAPTER
2. 1 51-4000 ADAPTER CASTING (Ref: 711140) (Assembled by AA)
3. 1 52-6201 COUPLER (27 X 23 Splines) (Ref: 711362-23) (Assembled by AA)
4. 1 52-6900 SHAFT (Ref: 711369)
5. 1 716063 COVER PLATE
6. 1 716072 RELUCTOR RING CLAMP RING
(One piece reluctor, bolt torque 10 ft-lbs.)
7. 1 716079 22mm PLUG
8. 1 716082 700R/4l60 NYLON BUSHING
9. 1 716289 SEAL SLEEVE (INSTALLED)
10. 1 716308 BEARING (#6209) (Assembled by AA)
11. 1 716450 SNAP RING (GM #378-5205) (Assembled by AA)
12. 1 716456 SNAP RING (T/A #N5000-334) (Assembled by AA)
13. 1 716511 "O"-RING (GM #135-8899)
14. 1 716563 GASKET
15. 1 716564 GASKET
16. 1 716712 SEAL (NAT #223440) (Installed in Casting by AA)
17. 4 720040 8mm X 1.25 X 20mm (Metrics)
18. 4 720046 METRIC S.H.C.S. 10mm-1.5 THR X 40mm
19. 1 300619 RELUCTOR SENSOR
In 1996, GM produced a newer version of its electronically controlled 4L60E. This 4L60E transmission is 21-1/2"
long, and has a removable bellhousing. It has a hex bolt pattern on the output side of the transmission, similar to a
TH400.
The 51-0405 adapter was designed to make this style of 4L60E look just like a 700R. By incorporating a new clamp-
on reluctor ring and sensor on this adapter, a 40 pulse per output shaft revolution signal is generated for the drivetrain
control module. This adapter comes with a new clamp-on reluctor ring that should be installed on the new 700R output
shaft that you have had installed in your transmission. This clamp-on reluctor ring clamps over the stock governor
gear on the 700R output shaft. We have provided two reluctor sensor locations to choose from in the adapter. The
hole not being used will need to be plugged with the plug provided.
Before tightening this clamp, trial fit the 51-0405 adapter plate onto the back of the 4L60E transmission. With the
adapter set on the back of the transmission, install the 300619 reluctor sensor into the adapter casting. The 300619
sensor should line up over the teeth of the reluctor clamp. When you obtain this location, remove the adapter housing,
making sure not to disturb the position of the clamp on the shaft. With the clamp now exposed, tighten the set screw
on the clamp.
(One piece reluctor, bolt torque 10 ft-lbs.)Loctite on these set screws is recommended.
Trial fit the 51-0405 adapter and 300619 sensor back on the transmission and make sure the reluctor ring teeth and
ADVANCE ADAPTERS
IN-HOUSE PROCEDURES
NOTE:
P/N 716289 must be installed and
loctited in place. Use Loctite 680.
Install seal before shipping
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels