ADVANCE ADAPTERS INC. P/N: 920001
P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 11-26-12
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.
KIT CONSISTS OF:
No. Qty. Part No. Description
SATURN OVERDRIVE SHIFT LINKAGE
T90 SINGLE T/C HANDLE SHIFTER
1. 1 715651 CLIP
2. 2 716039 SHIFTER BRACKET SPACER WASHER (T90)
3. 1 716140 BRAKE YOKE 3/8" WITH PIN
4. 4 722546 SHIFTER BOOT SCREWS
5. 2 723103 LOCK WASHER 5/16" PLATED
6. 2 723735 SPEC.SAE WASHER 3/8" I.D.
7. 2 723126 5/16"-18 x 2" H.H.C.S.
8. 1 920016 SHIFTER KNOB (SATURN)
9. 1 920017 WASHER
10. 1 920018 SHIFTER SNAP RING
11. 1 920019 SHIFTER HANDLE
12. 1 340605 SHIFTER BOOT UNIVERSAL
13. 1 340602 SHIFTER BOOT RING UNIVERSAL
14. 1 920031 T90 SINGLE LEVER SHIFT BRACKET
15. 1 920032 T90 SINGLE DUAL LEVER SHIFT ROD
16. 1 920039 1/4"-20 x 1" H.H.C.S.
17. 1 920040 1/4"-28 JAM NUT
18. 1 920041 HEIM JOINT 1/4"-28
19. 1 722514 1/4"-20 LOCKNUT
20. 1 303081 IGUS BUSHING (PRESSED INTO THE HANDLE)
The shifter assembly for the Saturn Overdrive is only available for the original T90 3 speed transmission, 1946-1966.
The shifter bracket fits directly over the top cover plate of the 3 speed transmission and the pivot extends outward
towards the passenger side of the vehicle. To access the assembly of the T90 transmission , the sheet metal tunnel
cover will need to be removed. When mounting the shifter bracket, you will need to use the steel spacer washers
between the top cover and the shifter bracket. New bolts have been supplied for the bracket assembly to the
transmission. The linkage rod must be installed into the slotted shift rail on the back side of the overdrive. The rod
must be slipped over the transfer case and certain installations may require modifications to the shifter rod. With the
extension rod in position and the shifter bracket in position, you can now install the handle assembly. The handle will
slip over the shifter bracket pin as illustrated. The clevis assembly (or brake yoke), will then slip onto the shifter
handle. At this point, the adjustment between the shifter handle and the linkage rod can be determined. The handle
should be positioned in a vertical position and the shifter rod in the overdrive should be positioned into the neutral
location
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels